知方号

知方号

屈服强度是什么意思<屈服拼音>

屈服强度是什么意思

全部

Oxgen precipitates ( useful for gettering ) can reduce the yield strength ( critical shear stress ) up to fivefole.

氧沉淀 ( 可用作吸杂 ) 会使屈服强度 ( 临界剪应力 ) 降低为五分之一.

辞典例句

Yielding strength is indicative of the stress at which plastic deformation begins.

屈服强度是指塑性形变开始发生时的应力.

互联网

The yield strength fy of reinforcement is used in design.

在设计中利用的是钢筋的屈服强度.

互联网

The rare earth lanthanum oxide doped molybdenum alloys containing different volume fraction lanthanum oxide particles werepowderprocessing.

结果表明,稀土氧化镧掺杂钼合金由于其细小的氧化镧颗粒和细小的晶粒的作用而具有较高的屈服强度.

互联网

The V - N microalloy steel with yield strength of 550 MPa is produced by EAF - CSP route.

目前,在EAF-CSP 流程中通过V -N 微合金化技术可成功生产屈服强度为550MPa的高强度低合金钢.

互联网

The yield strength ( σ0.2 ) , ultimate tensile strength ( σ b ) and elongation ( δ ) of A 356 - T 6 alloy were 240 MPa, 254.8 MPa and 1.16 % , respectively.

屈服强度 、 抗拉强度和伸长率分别为240MPa 、 254.8MPa和1.16%.

互联网

FIG. 5 shows the average yield strength as a function of extrusion speed and location.

图5示出了平均屈服强度与挤压速度和位置的关系.

互联网

Dislocation strengthening and grain refinement strengthening makes coil 059 with the higher yield strength.

位错强化与晶粒细化强化是059板卷具有高屈服强度的原因.

互联网

The result measured by this method is agreement with the actual data in production generally.

用此方法得出的钢管真实屈服强度与实际生产数据基本吻合.

互联网

The yield strength, tensile ratio and toughness are major quality indexes of steel pipe ( board ).

屈服强度 、 屈强比、韧性等是钢管 ( 板 ) 的主要质量指标,合理确定这些指标的数值有相当难度.

互联网

The creep rate was increased while the yield strength was reduced by anodic dissolution.

阳极电流不但使恒载荷下的不锈钢蠕变速度增加,而且使屈服强度下降.

互联网

CuPTiRE anti - erosion hot rolling stripes are divided into two grades in yield strength : 295 MPa, 345 MPa.

09CuPTiRE耐大气腐蚀热轧钢板按屈服强度分为295MPa级和345MPa级两个级别.

互联网

The results show that the steel has high yield strength and quality forming property.

结果表明,研制开发出的铌钛微合金化IF钢具有高的屈服强度和优良的成形性能.

互联网

Residual stress concentration a notch depends on both notch geometry and yield strength of the material.

缺口根部的残余应力存在应力集中效应,应力集中值不仅取决于缺口几何形状而且和材料的屈服强度有关.

互联网

版权声明:本文内容由互联网用户自发贡献,该文观点仅代表作者本人。本站仅提供信息存储空间服务,不拥有所有权,不承担相关法律责任。如发现本站有涉嫌抄袭侵权/违法违规的内容, 请发送邮件至lizi9903@foxmail.com举报,一经查实,本站将立刻删除。